1. One button to change two modes. High-speed mode: suitable for high-speed driving on the ground, sprinting uphill. Off-road mode: suitable for complex terrain and through various obstacles.
2. Ultra-simulated deep concave tires provide strong grip and wear resistance.
3. 4-wheel drive unit, easy to climb at a right angle of 90 degrees.
4. Can drive on both sides.
5. Remote control, multiplayer competition does not interfere with each other.

Specification:
1. Product size: 34x19x9cm.
2. Remote control frequency: 2.4GHz.
3. Remote control battery: 2 1.5V 5 batteries (purchased by yourself).
4. Body battery: 6. 0V 400mAh battery pack.
5. Charging time: 60 minutes.
6. Use time: 25 minutes.
7. Material: ABS/alloy fittings.
8. Climbing angle: greater than or equal to 45 degrees.
9. Suitable age: 6 years old or older.
10. Drive mode: four-wheel drive.
11. Remote control distance: about 40m.

1. Equipped with dual-strong magnetic motor, high-powered power output, high-efficiency engine power, four-wheel drive, rock climbing is easy and effortless.
2. Independent four-wheel suspension device absorbs the vibration caused by the bumpy road surface of the wheel. The upper and lower A arms will withstand the impact and pressure brought by the off-road, and the driving will be more stable.
3. With a large twist angle and flexible angle conversion, it can easily cope with the challenges brought by various road conditions.
4. Increase the tire design, run a circle equal to two laps, you can easily send and run, adapt to a variety of terrain.
5. Tire made of PVC rubber material, the texture is flexible, and the uneven tire texture increases the friction, making it easy to climb on any ground without difficulty.

Specification:
1. Product size: 28x17.5x14cm.
2. Control distance: 35m or more.
3. Charging time: 60 minutes.
4. Remote control time: 25 minutes.
5. Age of use: 2-14 years old.
6. Maximum speed: about 7 km/h.
7. Remote control: 2.4GHz wireless remote control.
8. The remote control requires 2 1.5V M batteries (purchased by yourself).

Note:
This product contains electronic components and should not be used in water or humid environments. When cleaning the stains, wipe the surface with a dry cloth.

The package contains:
Remote control car x 1
Remote control x 1
Remote control car battery x 1
Charger x 1

1. 1:16 original car scale, the details inside the car are realistic.
2. Four-wheel drive, double motor, 4 super shock absorber springs, strong climbing ability, adapt to a variety of outdoor scenes, such as: sand, grass, rocky beach, snow.
3. Hollow rubber tires with clear tire lines and non-slip wear resistance.
4. The remote control car needs to be charged for 2-4 hours before use.

Specification:
1. Car size: 17.5x27x15cm.
2. Material: ABS engineering plastic / electronic components / rubber.
3. Body battery: 4.8V/2000mAh.
4. Remote control battery: 2 x 1.5V AA (not included).

Packaging accessories:
Remote control car x 1
Remote control x 1
Remote control car battery x 1
USB charger x 1

Features:
1. Comes with 1500mAh high-rate lithium battery
2. 2.4G full-scale synchronous remote control system
3. 19g high-speed metal gear steering gear (2kg torque)
4. The front wheel torsion axle type independent horizontal damping suspension system, rear multi-link straight bridge suspension, efficient shock absorption
5. 35A brushless waterproof ESC
6. Damping independent metal shock absorber
7. Full vehicle dual CVD up-and-down drive shaft
8. Simulation of 3D roll cage car shell, disperse the impact from the ground, enhance the body strength and anti-torsion
9. Large size 3D TPR all-terrain off-road wheels, suitable for various roads
10. 2212 High Torque Outward Rotating Brushless Motor
11. Add a balance bar for better starting control
12. Add two spare tires to the body

Product parameters:
1. Material: hardware/electronics/plastic
2. Wheelbase/wheelbase: 20cm/24.9cm
3. Size: 39.8x23x18.2cm
4. Body weight (without battery): 1.52kg
5. Speed: up to 55km/H
6. Motor: brushless motor
7. Remote control frequency: 2.4GHz
8. Remote control distance: greater than or equal to 80m
9. Remote control time: about 25-30 minutes (depending on vehicle speed)
10. Charging time: about 3 hours
11. Body battery: 7.5V 1500mAh
12. Remote control battery: 4 x 1.5V AA batteries (need to be purchased separately)

1. Long service life, easy to install
2. Good quality and excellent performance
3. Very strong and light weight
4. Number of blades: 3
5. Weight: 2.3g/pcs
6. Center thickness: 6mm
7. Shaft: 5mm

1. Suitable for 2204, 2205, 2206 motor with 5mm bearing, and effectively fasten the propeller
2. The 4.5mm height nut is low profile type which is suitable for most of the motors
3. Lock Nuts ensure a secure hold; reduce slippage
4. Drive system is a hexagon-shaped head, self-locking, nylon insert
5. Coarse threads are better for brittle materials and will assemble and disassemble more quickly than fine threads
6. Material: aluminum alloy
7. Size: M5x6mm (height)

Notice:
CW nut means turn the nut clockwise to lock it
CCW nut means turn the nut counter-clockwise to lock it

1. Fit the size of the motor, will not scratch the body
2. Transit can protect the motor against bump
3. When not flying, motor can be protected from moisture
4. Has insulation Function
5. Anti-crash,can be used as support and buffer for antennaAnti-crash,can be used as support and buffer for antenna
6. Small and portable, easy to install
7. Material: PVC
8. Product size: 3x15mm

1. Designed for X-Class models
2. Exquisite appearance design, large airflow, reasonable structure, solid
3. High-precision CNC machining of the whole body, high strength and high precision
4.660KV pull force reaches 7.9KG
5. Adopt N45SH magnet to ensure the torque and ensure the high temperature does not lose magnetism
6.50%-90% throttle effect and thrust
7. The motor body has undergone precise dynamic balance processing to ensure the balance of the motor when it runs at high speed
8. EZO bearing, to ensure the smooth running of the motor
9. Tile-shaped magnet, very small gap
10. 420 stainless steel shaft
11. Optimize the design of heat dissipation structure, reduce 20% year-on-year
12. Reliable magnetic circuit optimization, excellent power conversion

parameter:
-KV: 660KV 400KV
-Structure: 12N14P
-Stator diameter: 42mm
-Output shaft length and diameter: 26.5mm M6
-Motor size: 50x33mm
-Magnet: N45SH
-Bearing: EZO
-Output wire diameter: 14awg, 800mm
-Weight: 208.8g

1. Made of high-quality rubber, long-lasting performance
2. Light weight, small size, easy to carry
3. M3 flight control damping ball effectively reduces the sensitivity of the flight control
4. The latest F4 flight controller used on the FPV quadcopter frame to prevent vibration
5. Product size: 6.6x6x3mm

1. The product is equipped with a 3.7V 300mAh lithium battery (included).
2. The remote control requires two 1.5V AA batteries (sold separately).
3. The 10-channel remote control can control: forward, backward, left forward, right forward, left backward, right backward, turn left on the spot, turn right on the spot, the bucket rises, and the bucket drops.
4. Suitable age: 6 years old and above.
5. Material: stainless steel + plastic.
6. Size: 21.5x13.7x12.8cm.
7. Number of blocks: 1178 blocks.

Packing list:
Track forklift assembly (set) x 1
Remote control x 1
Manual x 1
Charging cable x 1
Tools (set) x 1
Number of spare screws

1. Size: 19.8*11.8*12.2 cm
2. Weight: 416g
3. Fuselage battery: 3.6V 350mAh
4. Remote Controller Battery: AA*2 (to be purchased separately)
5. Charging time: 4-5 hours
6. Use time: about 18 minutes
7. Remote control distance: 30 meters
8. You can move forward and backward, turn left and turn right.
9. Front wheel 60 degree steering, rear wheel four-wheel drive.
10. High headlights in front, driving unimpeded at night.
11. Anti-skid and wear-resistant tire: vacuum inner liner, strong grip.
12. Iron Cover Motor: Driving motor uses iron cover motor, so that the service life of the car is longer.
13. Cargo in the garage: It can realize the delivery function within about 30 meters, and the simulation interaction is stronger (Note: When the maximum horsepower battery is full, the load is about 500 grams).
14. Product Accessories: English Instructions * 1 USB * 1 Battery * 1 Screwdriver *1

1. Product material: plastic+metal+electronic components.
2. Features: forward, backward, left, right, one key deformation.
3. Using time: 20min. Charging time:2h.
4. Control distance: 15m. Max speed:5km/h.
5. Battery: NI-CD 1.2V 700mah.
6. Transmitter battery: 2x1.5AA(not included).

1. Product material: plastic+metal+electronic components.
2. Features: forward, backward, left, right, one key deformation.
3. Using time: 20min. Charging time:2h.
4. Control distance: 15m. Max speed:5km/h.
5. Battery: NI-CD 1.2V 700mah.
6. Transmitter battery: 2x1.5AA(not included).

1. Open the ON/OFF switch on its body and put your hands on the transmitter.
2. 4 legs which can be moving respectively allow the mouse to crawl noiselessly on any smooth surface.
3. Tail swing up and down when running.
4. Realistic looking mouse with black fur.
5. Have a good laugh scaring your friends and family.

1. Use powerful & high performance MCU. Users can set functions as their demand, fully embody Intelligent characteristics. Unique circuit design, strong
anti-interference.
2. Waterproof design (Note: if there is water in the ESC, Please dry the water at the connectors).
3. Start mode can be set, throttle responses fast, and it has a very smooth speed control linearity. Compatible with scale boat & racing boat.
4. Low-voltage protection threshold value can be set.
5. Built-in switch BEC, large power load with servo, lower power dissipation.
6. Multiple protection functions: input voltage abnormal protection / low-voltage cutoff protection, over-thermal protection and throttle signal loss protection,
make the ESC more reliable.
7. High power safety performance: wherever the throttle lever is, the motor will not start immediately.
8. Over thermal protection: when ESC temperature is over 100 Celsius degree, output power will automatically reduce. When it''s lower than 80 Celsius degree output power will return to normal.
9. Cycle menu setting, simple operation. Support setting with program box and transmitter.
10. Suitable for boats with less than 120cm length.

1. Adopting simulation structure design, it has the control feeling of a real car, realizing full-scale continuously variable transmission, high-speed driving, rapid acceleration, deceleration, braking, reverse, left turn, right turn
2. Applicable venues: flat ground, sandy ground, mud ground, grassland
3. Four-wheel drive: front and rear upright spring damping, double-wishbone independent suspension system
4. 2.4G full-scale synchronous remote control system. Full-scale throttle/steering
5. 2.4G splash-proof four-way 30A integrated ESC/receiver
6. Front wheel cross ball joint universal joint drive shaft, rear wheel split dog bone drive shaft
7. Five-wire 17G steering gear
8. Super battery power: 7.4V, 18650-1300mAh Li-ion battery (T plug), discharge rate 10C
9. The whole car adopts 16 ball bearings
10. Metal second floor, metal front and rear arm codes, metal middle drive shaft
11. The car shell adopts high toughness explosion-proof PVC car shell
12. Equipped with LED headlights (three modes: always on, slow flashing, fast flashing)
13. Equipped with head-up wheel
14. Imitation bigfoot tires, strong grip

Parameter:
1. Material: metal, electronic component, plastic
2. Motor: RC390 high-speed carbon brush strong magnetic
3. Frequency: 2.4GHz
4. Remote control distance: >=80 meters
5. Remote control battery: 3 x AA batteries (not included)
6. Body battery: 7.4V 1300mAH Li-ion battery
7. Control time: 12-15 minutes (continuous running at full speed)
8. Charging time: 2-2.5 hours (USB cable charger)
9. Wheelbase 188mm, wheel diameter 85mm
10. Speed: 38 km/h
11. Body size: 30x23x11.5cm
12. RC size: 13x7.5x21cm
13. Body weight: 930g
14. Weight of RC: 170g

1. Product size: 26.5 x 16 x 13.5cm
2. Body battery: 3.7v 650mAh
3. Remote control battery: 2 x AA battery(Not included)
4. Charging time: about 4-5 hours
5. Usage time: about 20 minutes
6. Remote control distance: 20 to 30 meters
7. Unique modeling and simulation design
8. 2.4G remote control, convenient and easy to use

1. The design is suitable for the driving firmware of the three-phase brushless, sensorless motor, with smooth, exquisite speed adjustment and linear speed adjustment.
2. Using high performance MCU, low resistance MOSFET and other imported components. High reliability, low impedance circuit board with strong resistance to current. Produce less heat.
3. 8 run acceleration options. It applies to all kinds of different RC car models.
4. 8 types of inlet angle can be used to make the motor work at the optimum efficiency points.
5. Good protection function: low voltage protection, over-temperature protection, loss of throttle signal, motor plugging, etc.
6. Easy to use: the settings of the motor can be set by remote control or program card, with sound notification.

1. Control Channels: 6 Channels.
2. Movement Direction: forward, backward, left, right.
3. Transmitter Frequency: 2.4G.
4. Control Distance: about 15m.
5. Battery for Car: 3.7V 800mAh rechargeable battery pack(Included).
6. Battery for Transmitter: 2 x 1.5V AA Batteries(No Included).
7. Running time: about 30mins,charging time: 120mins.
8. Product Size: 14x25x9cm.

1. Product size: 25 x 12 x 8cm
2. Body battery: 3.7v 650mAh
3. Remote control battery: 2 x AA battery(Not included)
4. Charging time: about 1.5 hours
5. Usage time: about 20 minutes
6. Remote control distance: 40-50 meters
7. It is the best gift for children

1. Use powerful & high performance MCU. Users can set functions as their demand, fully embody Intelligent characteristics. Unique circuit design, strong
anti-interference.
2. Waterproof design (Note: if there is water in the ESC, Please dry the water at the connectors).
3. Start mode can be set, throttle responses fast, and it has a very smooth speed control linearity. Compatible with scale boat & racing boat.
4. Low-voltage protection threshold value can be set.
5. Built-in switch BEC, large power load with servo, lower power dissipation.
6. Multiple protection functions: input voltage abnormal protection / low-voltage cutoff protection, over-thermal protection and throttle signal loss protection,
make the ESC more reliable.
7. High power safety performance: wherever the throttle lever is, the motor will not start immediately.
8. Over thermal protection: when ESC temperature is over 100 Celsius degree, output power will automatically reduce. When it''s lower than 80 Celsius degree output power will return to normal.
9. Cycle menu setting, simple operation. Support setting with program box and transmitter.
10. Suitable for boats with less than 100cm length.

1. Made of lightweight CNC machined aluminum and low carbon steel materials.
2. Additional handbrake for racing: independent and additional game equipment to control the racing game.
3. Progressive handbrake: non-contact switch, Hall sensor, higher accuracy and longer life.
4. Independent USB cable: plug and play, easy to install, only supports PC Windows system.
5. Sim Racing universal handbrake: Support Logitech G27 G25 G29 T500 T300 FANATECOSW LFS DIRT RALLY.

1. Material: PP cotton filling, knitted fabric
2. Bottom power switch
3. Plush flower pots, realistic modeling
4. Built-in lithium battery
5. Function: 120 English songs, recording
6. Size: 32cmx10cm
7. Weight: 0.25kg

Features:
1. Support audio/video at the same time, the picture quality is clearer, the picture is not cut, can support multiple mobile phones to watch video at the same time, can display 3D dual screen, support mobile phone recording, support device-side recording (need to add memory card)
2. Users can make full use of smart terminals as displays and video recorders during FPV flight, which is simple and convenient
3. Input the AV signal of the image transmission receiver, the forwarding distance (unobstructed) is greater than 150 meters, and it can also be used directly
4. Under the condition of inputting the AV signal of the image transmission receiver, no signal and weak signal are all snowflakes, which can save your love machine to the greatest extent
5. Wirelessly send to Android, IOS system mobile phones or tablets via WiFi, WiFi has no interference to 2.4G remote control
6. The APP software is simple and easy to use, supports display, zoom, video, screenshot and playback, and supports setting hotspot passwords
7. 9-30V wide voltage DC power supply, with power output port at the same time, convenient for power supply for image transmission
8. Support Android 4.3 or higher system version, support IOS 10.3 or higher system version
9. The delay is small, not more than 150 milliseconds for Android phones and tablets, and about 100 milliseconds for IOS phones and tablets
10. Suitable for wireless surveillance, video recorders, wireless rearview cameras, set-top boxes, engineering treasures, etc.

Product parameters:
1. Transmitting frequency: 2400MHz-2483.5MH
2. Transmission distance: more than 150 meters
3. Video input format: CVBS (NTSC/PAL)
4. Video input amplitude: 1.0Vp-p
5. Video input impedance: 75 ohms
6. Video frames: 30fps
7. Video format: VGA
8. Video compression: H.264
9. Wireless support: IEEE 802.11b, IEEE 802.11g, IEEE 802.n (1T1RModes)
10. Power supply: DC 9-30V
11. Current: 250mA
12. Encryption mode: WPA2
13. Waterproof: yes
14. Weight: 80g+/-5g
15. Dimensions: 78x43x18mm
16. Working temperature: -10-50 degrees Celsius

Packing list:
Transmitter x 1
Signal bar x 1
Power cable x 1
Manual x 1
Tape x 1
Strap x 2

1. Small and light enough you can carry it easily anywhere.
2. It is easily connected via Bluetooth, easy pairing with cellphone.
3. This USB adapter will connect to any Bluetooth audio device when you plug into your PS4 USB slot. It comes with a wireless microphone that will enable you to chat when you plug into the PS4 controller.
4. Play and plug.
5. Usage method:
(1). Turn on the power of the PS4 and plug the Bluetooth adapter into one of the USB ports of the PS4
(2). For the first time, the adapter is plugged into the PS4 USB port, the blue light flashes slowly, long press the button for about 2 seconds, the blue light flashes quickly, enter the pairing state, then turn on the Bluetooth headset and enter the pairing state, waiting for the USB adapter The connection with the Bluetooth headset is completed. When the connection is successful, the blue light of the USB adapter becomes steady, indicating that the Bluetooth is connected
(3). Plug the microphone into the headphone jack of the PS4 handle
(4). Enter the PS4 settings interface
(5). Select to enter the Peripheral Machine menu
(6). Select sound device
(7). Set Input Device to USB Headset (USB Audio Device)
(8). Set Output Device to USB Headset (USB Audio Device)
(8). Adjust the microphone volume and test the microphone volume at the same time, press the OK key to complete the setting
(10). Adjust the headphone volume to a suitable size
(11). Set output to headphones for all sounds
(12). Now, you can use the Bluetooth headset to listen to the sounds in PS4 games and enjoy unfettered game fun

1. Automatic calibration without manual.
2. There is no open space, no looseness.
3. Detachable bottom frame, suitable for multiple scenes.
4. High-precision sensor, no virtual position.
5. Comfortable grip and free adjustment.
6. USB interface, plug and play.

1. Use powerful & high performance MCU. Users can set functions as their demand, fully embody Intelligent characteristics. Unique circuit design, strong
anti-interference.
2. Waterproof design (Note: if there is water in the ESC, Please dry the water at the connectors).
3. Start mode can be set, throttle responses fast, and it has a very smooth speed control linearity. Compatible with scale boat & racing boat.
4. Low-voltage protection threshold value can be set.
5. Built-in switch BEC, large power load with servo, lower power dissipation.
6. Multiple protection functions: input voltage abnormal protection / low-voltage cutoff protection, over-thermal protection and throttle signal loss protection,
make the ESC more reliable.
7. High power safety performance: wherever the throttle lever is, the motor will not start immediately.
8. Over thermal protection: when ESC temperature is over 100 Celsius degree, output power will automatically reduce. When it''s lower than 80 Celsius degree output power will return to normal.
9. Cycle menu setting, simple operation. Support setting with program box and transmitter.
10. Suitable for boats with less than 55cm length.

1. Use powerful & high performance MCU. Users can set functions as their demand, fully embody Intelligent characteristics. Unique circuit design, strong
anti-interference.
2. Waterproof design (Note: if there is water in the ESC, Please dry the water at the connectors).
3. Start mode can be set, throttle responses fast, and it has a very smooth speed control linearity. Compatible with scale boat & racing boat.
4. Low-voltage protection threshold value can be set.
5. Built-in switch BEC, large power load with servo, lower power dissipation.
6. Multiple protection functions: input voltage abnormal protection / low-voltage cutoff protection, over-thermal protection and throttle signal loss protection,
make the ESC more reliable.
7. High power safety performance: wherever the throttle lever is, the motor will not start immediately.
8. Over thermal protection: when ESC temperature is over 100 Celsius degree, output power will automatically reduce. When it''s lower than 80 Celsius degree output power will return to normal.
9. Cycle menu setting, simple operation. Support setting with program box and transmitter.
10. Suitable for boats with less than 135cm length.

1. Function: Walk, light, sound effect, launch soft bullet.
2. Material: plastic / plastic.
3. Power supply mode: battery (sold separately).
4. Product size: 32x11x17cm.
5. Suitable age: 6 years old and above.

1. The front of the car is anti-collision.
2. Climb the 15-118 degree slope.
3. Rubber tires for easy driving of multiple venues.
4. Off-road modeling, the body has a texture.

Specification:
1. Material: ABS material + electronic components.
2. Product size: 19x12x9cm.
3. Remote control mode: 27Mhz wireless remote control.
4. Drive mode: rear drive.
5. Driving speed: 12-14 Km/h.
6. Body battery: 3.6V 300mAh rechargeable battery pack.
7. Remote control appliance: 2 AA batteries (not included).

1. The product is equipped with a 3.7V 300mAh lithium battery (included).
2. The remote control requires two 1.5V AA batteries (sold separately).
3. The 10-channel remote control can control: forward, backward, turn left, turn right, turn left in place, turn right in place, the boom is raised, the boom is lowered, the hook is raised, and the hook is lowered.
4. Suitable age: 6 years old and above.
5. Material: stainless steel.
6. Size: 34.5x22.5x35cm.
7. Number of blocks: 1745 blocks.

Packing list:
Side crane assembly (set) x 1
Remote control x 1
Manual x 1
Charging cable x 1
Tools (set) x 1
Number of spare screws

1. Alloy material, realistic texture, resistant to falling and crashing.
2. Equipped with dual-strong magnetic motor, high-powered power output, high-efficiency engine power, four-wheel drive, rock climbing is easy and effortless.
3. Independent four-wheel suspension device absorbs the vibration caused by the bumpy road surface of the wheel. The upper and lower A arms will withstand the impact and pressure brought by the off-road, and the driving will be more stable.
4. With a large angle of twisting and flexible angle conversion, it can easily cope with the challenges brought by various road conditions.
5. Increase the tire design, run a circle equal to two laps, you can easily send and run, adapt to a variety of terrain.
6. Tire made of PVC rubber material, the texture is flexible, and the uneven tire texture increases the friction, making it easy to climb on any ground without difficulty.

Specification:
1. Product size: 36x22.5x19.5cm.
2. Control distance: 35m or more.
3. Charging time: 60 minutes.
4. Remote control time: 25 minutes.
5. Material: Alloy.
6. Age of use: 2-14 years old.
7. Maximum speed: about 7 km/h.
8. Remote control: 2.4GHz wireless remote control.
9. The remote control requires 2 1.5V M batteries (purchased by yourself).

Note:
This product contains electronic components and should not be used in water or humid environments. When cleaning the stains, wipe the surface with a dry cloth.

The package contains:
Remote control car x 1
Remote control x 1
Remote control car battery x 1
Charger x 1